Characterization of catalytic chemical vapor-deposited SiCN thin film coatings

  • Suresh Neethirajan1Email author,

    Affiliated with

    • Takahita Ono2 and

      Affiliated with

      • Esashi Masayoshi2

        Affiliated with

        International Nano Letters20122:4

        DOI: 10.1186/2228-5326-2-4

        Received: 8 April 2012

        Accepted: 7 June 2012

        Published: 7 June 2012


        Silicon carbonitride thin films of 480 to 730-nm thicknesses were grown on silicon substrate using ammonia and hexamethyldisilazane gas sources using catalytic chemical vapor deposition process. Compositions of silicon, carbon and nitrogen in the SiCN films were varied by changing the flow rate of ammonia gas. The effect of deposition conditions on the structural, optical and mechanical properties of SiCN thin films was examined. X-ray photoelectron spectroscopy analysis indicated that the higher flow rate of ammonia gas results in higher nitrogen and lower carbon content in the deposited thin films. The measurement of stress as a function of substrate temperature in the SiCN film showed that the stress changes from compressive to tensile in the range of 275°C to 325°C. With these preliminary characterization tests, it is expected that SiCN nano-thin films can be used for developing sensors for harsh environment.


        SiCN Catalytic chemical vapor deposition Thin films XPS


        Polymer-derived ceramic materials such as silicon carbonitride (SiCN) are gaining momentum because of their excellent thermal and mechanical properties at high temperatures. In addition, the electrical conductivity of SiCN can be tailored and characterized to suit specific application needs. These unique properties make SiCN a best choice for sensor applications. SiCN has the potential to be used for making heat flux sensors [1], health monitoring sensors for turbines and power generation systems [2] and high temperature pressure transducers [3]. Because of temperature dependence on the resistance of the SiCN film, the potential of making gas/temperature sensor using SiCN films is enormous. For high temperature, corrosive and harsh environmental applications in the agricultural and food industry, SiCN-based sensors are preferred.

        Experimental methods for making thin films of SiCN to facilitate sensor fabrication are being researched worldwide. Radio frequency magnetron sputtering [4, 5], pulsed laser deposition [6], plasma-enhanced chemical vapor deposition (CVD) [7], microwave plasma-enhanced CVD and electron cyclotron resonance plasma CVD [8], ion beam sputtering [9], hotwire CVD [10] and other methods of depositing SiCN films have been explored. The advantages of catalytic CVD over PECVD and other deposition techniques include higher deposition rate with lower strain, reduced thermally induced stress on the substrate and low processing cost. Parameter regimes such as influence of flow rates of target gas and variation in substrate temperature need to be identified for effective deposition of SiCN thin films. This work focuses on the optimization of SiCN films using hexamethyldisilazane (HMDS) and ammonia gasses, and investigation of the effect of deposition conditions. The correlation between process parameters and the structural, optical and mechanical properties of the fabricated SiCN thin films with various deposition conditions are reported.

        Experimental details

        The SiCN films were deposited using a catalytic CVD reactor (Figure 1; custom built by Universal Systems Co., Tokyo, Japan) on n type (100)-oriented Si wafer of 380-μm thickness. Prior to deposition, silicon wafers were cleaned using RCA cleaning process. Tungsten wires of 0.5-mm diameter were used as a catalytic filament and were heated by flowing current. The distance between substrates and filament was set to be 5 cm. The filament temperature was controlled by flowing current through the filament and was measured by a digital pyrometer (Chino 760, Tokyo, Japan). The substrate was heated using an embedded heater, and the temperature was measured using a thermocouple attached to the substrate holder. The CVD system consists of a HMDS liquid tank. Argon was used as a carrier gas at constant flow rate to carry HMDS into the reaction chamber. The flow of Ar + HMDS and NH3 was controlled by mass flow controllers in both gas lines. Before the deposition of a thin film, the reaction chamber was evacuated using a turbo molecular pump.
        Figure 1

        Photograph and schematic cross-section of the custom-built catalytic CVD apparatus.

        The filament temperature was maintained at 1,550°C. The varying deposition conditions are shown in Table 1. The deposition time was between 10–15 min. The chemical composition of the films was determined by X-ray photoelectron spectroscopy using MgKα radiation. The refractive index was obtained using a prism coupler (Metricon Model 2010, Metricon Corporation, NJ, USA). Film thickness was measured using FE-SEM (Model S-4500, Hitachi High-Technologies Corporation, Tokyo, Japan). SiCN film residual stress was calculated by measuring the radius of wafer curvature before and after film deposition using a thin film stress measurement system (Tencor P10 Surface Profiler, Tencor Systems Inc., Ontario, Canada) according to Stoney’s equation [11]:
        where E is the Young’s modulus for substrate, and γ is its Poisson’s ratio; D and t are the thicknesses of the substrate and the film, respectively; r1 and r are the radius of wafer curvature before and after film deposition, respectively.
        Table 1

        Deposition conditions of SiCN films

        Deposition conditions of SiCN films




        HMDS + Ar, NH3

        HMDS + Ar flow rate

        5 sccm

        NH3 flow rate

        0-60 sccm

        Background pressure

        0.13 Pa

        Substrate pressure

        200°C, 300°C

        Filament pressure


        Filament-sample pressure

        5 cm

        Results and discussion

        Structural property

        In a SiCN thin film, C-N bonds contribute to electrical conductivity and higher hardness, while Si-C bonds complement mechanical property. Hence, the properties of SiCN films can be tuned for need-based applications by changing the composition ratio. The influence of ammonia flow rate on the chemical composition ratio of the SiCN films are shown in Figure 2. Films deposited using lower than 10-sccm NH3 flow rate contains more than 40% carbon content. Nitrogen content gradually increased from 23% to 39% as the flow rate increased, while the carbon content decreased from 41% to 19% at 200°C substrate temperature. The comparison between deposition condition of 200°C and 300°C substrate temperatures reveals that silicon concentration decreased with increasing temperature. This analysis indicates that the carbon content in the SiCN films can be increased by increasing HMDS flow rate or by decreasing ammonia flow rate or both. The film thickness was measured using an optical profiler and was found to be ranging from 480 to 720 nm.
        Figure 2

        Relationship between ammonia flow rate and chemical composition of SiCN films.

        Optical property

        The refractive index of SiCN thin films measured using interferometer varied in the range of 2.5 to 2.2 for 200°C substrate temperature. The refractive index decreased with an increase in flow rate of ammonia. This may be due to the increased nitrogen concentration in the SiCN thin film. The value of refractive index decreased with increasing substrate temperature (Figure 3). For fabrication of micro-mirrors and anti-reflective coatings of solar cell applications, the refractive index of SiCN can be tuned and tailored.
        Figure 3

        Variation of refractive index with ammonia flow rate for SiCN films.

        Mechanical property

        The stress as a function of substrate temperature in the SiCN film is shown in Figure 4. The stress is compressive below 330°C, and it becomes tensile as the temperature increases. There is a steady increase in tensile stress once the temperature reaches 350°C and above. The value of stress at 50°C is 1,200 MPa compressive and at 400°C is 300 MPa tensile. The stress changes from compressive to tensile in the range of 275°C to 325°C. Higher tensile stress on cantilever structures made of SiCN thin films will lead to fracture, while compressive stress will cause buckling. Hence, during fabrication of SiCN film-based micro-devices, it is optimum to do the deposition at 330°C.
        Figure 4

        Variation of stress with substrate temperature for SiCN films.


        Silicon carbonitride films were successfully fabricated by catalytic chemical vapor deposition using hexamethyldisilazane and ammonia as source gasses. The chemical composition ratio as well as the refractive index of SiCN film can be changed by altering the flow rate of ammonia gas. The correlation between stress and substrate temperature indicates that the optimum deposition temperature of SiCN film for the fabrication of cantilevers and other micro-structures is around 330°C.



        The authors gratefully acknowledge the Department of Nanomechanics, Tohoku University, Japan for providing access to clean room and equipment facilities. Authors also thank the Japan Society for the Promotion of Science and the Natural Sciences and Engineering Research Council of Canada for funding this study.

        Authors’ Affiliations

        Biological Engineering, University of Guelph
        Graduate School of Engineering, Tohoku University


        1. Nagaiah NR, Kapat JS, An L, Chow L: Novel polymer derived ceramic-high temperature heat flux sensor for gas turbine environment. J. Phys: Conf. Series 2006, 34:458–463.View Article
        2. Leo A, Andronenko S, Stiharu I, Bhat RB: Characterization of thick and thin film SiCN for pressure sensing at high temperatures. Sensors. 2010, 10:1338–1354.View Article
        3. Liew L, Saravanan RA, Bright VM, Dunn ML, Daily JW, Raj R: A novel micro glow plug fabricated from polymer-derived ceramics: in situ measurement of high-temperature properties and application to ultrahigh-temperature ignition. Sens. Actu. A: Phys. 2003, 15:246–262.View Article
        4. Xie E, Ma Z, Lin H, Zhang Z, He D: Preparation and characterization of SiCN films. Opt. Mat. 2003, 23:151–156.View Article
        5. Sundaram KB, Alizadeh Z, Todi RM, Desai VH: Investigations on hardness of rf sputter deposited SiCN thin films. Mater Sci Eng 2004, 368:103–108.View Article
        6. Park N, Kim SH, Sung GY: Band gap engineering of SiCN film grown by pulsed laser deposition. J. App. Phy. 2003, 94:2725–2728.View Article
        7. Fischer LM, Wilding N, Gel M, Evoy S: Low-stress silicon carbonitride for the machining of high-frequency nanomechanical resonators. J. Vac. Sci. Tech B. 2007, 25:33–37.View Article
        8. Chen LC, Chen KH, Wei SL, Kichambare PD, Wu JJ, Lu TR, Kuo CT: Crystalline SiCN: a hard material rivals to cubic BN. Thin Solid Films. 1999, 355:112–116.View Article
        9. Zhou F, Yue B, Wang X, Wu X, Zhuge L: Surface roughness, mechanical properties and bonding structure of silicon carbonitride films grown by dual ion beam sputtering. J. Alloy. Compd. 2010, 492:269–276.View Article
        10. Nakayama H, Ito M: Super H2O-barrier film using Cat-CVD (HWCVD)-grown SiCN for film-based electronics. Thin Solid Films. 2011, 519:4483–4486.View Article
        11. Stoney GG: The tension of metallic films deposited by electrolysis. Proc. R. Soc. London, Ser. A 1909, 82:172–175.View Article


        © Neethirajan et al.; licensee Springer. 2012